Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Norman Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning and service in Norman, working on stainless flexible liners every week. What makes our DuraFlex work different is the fact that we see these liners at their failure points – top plates, tee snouts, insulation wrap, and smooth-wall creosote – not just at the firebox mouth. DuraFlex is a flexible stainless steel chimney liner, and like any liner system it needs care specific to how it’s built and how it’s installed.
To be clear up front: we are an independent DuraFlex service provider. We are not affiliated with, authorized by, or acting as warranty agents for DuraFlex. We simply know these liners well from field volume and code knowledge. If you own a home in Norman with a DuraFlex liner and want it swept, inspected, or repaired, call (888) 561-3468 for a free estimate.
Why Trust Chimney Sweep Norman for Your DuraFlex Chimney Cleaning?
Our technicians have up to experience, and a good share of that has been spent working on DuraFlex liners in Norman and the surrounding area. We know how a DuraFlex SW smooth-wall liner behaves when glazed creosote builds up, how ProFlex installations hold up over time, and where insulated liner kits tend to settle or wrap down. That familiarity matters when you’re deciding whether to sweep, repair, or reline.
We use quality parts that fit DuraFlex equipment – genuine DuraFlex top plates, caps, tees, and appliance connectors where they fit the existing liner, and quality aftermarket stainless hardware only where OEM isn’t practical. Off-brand thin-gauge fittings are exactly where these systems fail, and we won’t put them on a chimney we’re responsible for.
Warranty-safe service is part of the job. A liner installed to code with the right clearances and the right cap and top plate should stay in service for years. When we work on a DuraFlex system, we handle it in a way that respects the original installation and the manufacturer’s requirements. And if we find something that would compromise that, we tell you before we do the work – no surprises.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Norman
DuraFlex liners are built well, but they aren’t immune to the kind of wear a Norman chimney sees. Here are the specific problems we run into most often.
- Top-plate and cap connections loosening or rusting out. This is the most common failure we see. The top plate and cap sit at the crown, exposed to Norman’s freeze-thaw cycles and spring storms. When they loosen or rust through, water runs down the outside of the liner and into the smoke chamber. You can’t always see it from the ground – it shows up on a Level 2 scan or as rust and staining around the damper frame.
- Tee snout and appliance-connector joints pulling apart or corroding. On offset installs, the tee snout and the connector that meets the appliance take the most abuse. Condensate collects there, and over time those joints corrode or pull loose. That disrupts draft and lets creosote and moisture work into places they shouldn’t be.
- Smooth-wall liners caked with glazed creosote. A DuraFlex SW smooth-wall liner is designed for good draft, but when a wood stove runs with restricted draft, glazed creosote builds up inside it. The smooth surface hides how thick the glaze has gotten until the sweep starts. That glaze is what restricts draft further and raises the risk of a chimney fire.
- Insulation wrap degrading or pour mix settling. Insulated liner kits are rated for zero clearance, but only while the insulation is intact. After years of heating and cooling, the wrap can degrade or the pour mix around the liner can settle. What was a properly insulated liner is now, effectively, running without its insulation – and nobody notices until an inspection.
- Cracked or missing top plates and failed flashing. At the crown, a cracked or missing top plate and failed flashing let water track alongside the liner and rust the damper frame and firebox. Norman’s humid summers and hard freezes make this wear faster than you’d expect. Repointing old brick and resetting flashing is often the fix, but replacing the top plate is just as important.
Here’s how this kind of job usually goes. A homeowner with a wood stove or insert on a DuraFlex smooth-wall liner calls because the draft has gone flat and smoke rolls back when the door opens. On a Level 2 scan, the sweep typically finds glazed creosote built up in the top third of the liner and a top plate that’s loose or rusted, so water and draft are both leaking past the crown. The usual fix is a proper sweep with stiff poly or a rotary head that won’t scar smooth-wall stainless, resecuring or replacing the top plate and cap, and rechecking the tee and connector joints before the firebox goes back into service.
DuraFlex Parts & Our Repair-vs-Replace Approach
We use genuine DuraFlex top plates, caps, tees, and appliance connectors where they fit the existing liner. Where OEM isn’t practical, we use quality aftermarket stainless clamps and hardware – not thin-gauge substitutes. We don’t claim to stock or order genuine DuraFlex parts on every job; if a part needs to come from the manufacturer, we’ll tell you and factor it into the estimate.
The repair-vs-replace call is where we’re most honest with Norman homeowners. Not every problem needs a new liner. A liner with a tight top plate and sound joints can often be swept and kept in service. But a corroded or improperly insulated liner that’s this far gone usually gets replaced, not patched. The difference comes down to the top plate, the joints, and the insulation – and we can show you what we’re seeing. Call (888) 561-3468 to talk through your options.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection – a camera scan of the liner from firebox to cap. We’re looking at creosote buildup, the condition of the top plate and cap, the tee and connector joints, and the state of the insulation.
- 2
Repair or install. Based on what the scan shows, we recommend a sweep, a repair (top plate, cap, tee, connector), or a reline – and we explain why before any work begins.
- 3
Test. After the work, we run a draft test and verify the joints and top plate are tight. We photograph the finished liner so you have a record.
- 4
Warranty. If DuraFlex’s warranty applies to your system, we service the liner in a way that respects it. We aren’t warranty agents, but we can tell you what the original installation required and whether the work you need is warranty-safe.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Norman
We service and install the full range of DuraFlex flexible stainless liner systems, including DuraFlex SW smooth-wall relining kits, DuraFlex ProFlex flexible stainless liner, DuraFlex insulated liner kits (with insulation wrap or pour mix), and DuraFlex rigid stainless pipe sections along with the tee and elbow fittings used in offset runs. Whether your Norman home has a straight run or an offset that a rigid liner can’t handle, a flexible DuraFlex system is often the answer. We don’t claim to stock every component – if a part needs to come from the manufacturer, we’ll say so.
We Also Service These Brands
We’re not tied to a single brand. Alongside DuraFlex, we work with HeatShield, the ceramic resurfacing system that lets us restore a deteriorating flue liner without full relining, and Gelco caps. That matters in Norman, where some chimneys need a liner and others need a HeatShield restoration instead. One team, one standard.
FAQs – DuraFlex Chimney Cleaning Service in Norman
No. We are an independent DuraFlex service provider. We are not authorized, sponsored, or acting as warranty agents for DuraFlex. We work on DuraFlex liners because we know them well and see them often, not because the manufacturer endorses us.
Yes. We use genuine DuraFlex top plates, caps, tees, and appliance connectors where they fit the existing liner, and quality aftermarket stainless hardware only where OEM isn’t practical. We avoid off-brand thin-gauge fittings, which is where these systems tend to fail. Call (888) 561-3468 for an estimate.
Most DuraFlex sweeps and inspections are done in a single visit, usually a few hours depending on the liner and access. A repair like a top plate or cap replacement is often same-day. A reline can take longer. The written estimate sets the timeline before we start.
We service DuraFlex SW smooth-wall relining kits, ProFlex flexible stainless liner, insulated liner kits with wrap or pour mix, and the rigid pipe sections and tee/elbow fittings used in offset runs. If you’re not sure which system you have, a Level 2 inspection will tell you.
It shouldn’t, if the service respects the original installation. We handle DuraFlex liners in a way that’s warranty-safe, and we can tell you what the original installation required. We aren’t warranty agents for DuraFlex, so any warranty claim would still go through the manufacturer.
An annual sweep is typically the lowest-cost service and is quoted per job by the written estimate; a top plate or cap repair costs more, and a reline costs more still. We don’t quote a number before we’ve seen the liner. Call (888) 561-3468 for a free estimate – we’ll tell you whether you need a sweep, a repair, or a reline.
Yes. We use stiff poly brushes or a rotary head on smooth-wall stainless so the liner is cleaned without scarring the surface. A scratched liner collects creosote faster, so this matters. The right tool depends on the liner and the creosote, and we check before we start. Call (888) 561-3468 to book a sweep.
You usually can’t tell from the firebox. Insulation wrap degrades and pour mix settles quietly, so a liner rated for zero clearance can be running without its insulation. A Level 2 inspection with a camera scan is how you find out. If it has failed, we’ll tell you whether it’s a repair or a reline.
Often it’s a repair. A rusted or loose top plate and cap can usually be replaced and resecured without replacing the liner, as long as the liner itself is sound. If the scan shows corrosion on the liner or failed joints, a reline may be the better call. We’ll show you the evidence and let you decide.
Yes. A gas fireplace on a DuraFlex liner still needs an annual inspection, and often a sweep. Gas logs and occasional wood burning soot up short, straight flues quickly, and the top plate and cap still take weather. Annual service catches small issues before they become relines.
A Level 1 inspection is a visual check of the firebox and accessible parts of the liner. A Level 2 inspection adds a camera scan of the full liner, the top plate, the cap, and the joints – which is what a DuraFlex installation needs to confirm the liner is sound. We recommend a Level 2 scan for any liner we haven’t seen before.
Book Your DuraFlex Service in Norman, OK
If you own a home in Norman with a DuraFlex liner and you’re not sure whether you need a sweep, a repair, or a reline, we can tell you. We service DuraFlex SW, ProFlex, and insulated liner systems, along with HeatShield and Gelco. Call (888) 561-3468 for a free estimate. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Norman.